Nationwide: Corp. 800-221-3332
Mustang, OK: 281-546-7681
Nashville, TN: 615-507-4884

Bismarck, ND 281-546-7681
Houston, TX:
832-554-7811
Temecula, CA: 951-926-4849

Twitter Tweet with us Facebook us Linked In with us

All Pipe Freezing Kits and Aluminum Freeze Jackets

Complete 1/2"-4" Single Freeze Kit

Freezing Kit

Qty: Price: $569.00

Pipe Freezing Operating Instructions Manual PDF

The Pipe Freezing Kit eliminates the need to drain systems and shut down operating equipment when making pipe repairs. The kit uses liquid carbon dioxide to create ice plugs in sections of pipes. Kits are supplied with three freezing jackets for pipes ½"-4" (13-77mm) O.D.

To operate, turn off the pipe flow and attach a freezing jacket to the pipe upstream from the section needed to be repaired. Fill the freezing jacket with CO2 and an ice plug will form. After completing whatever work is needed, remove the jacket and the ice plug will defrost.

Note:
The Kit can be used for pipes ½"-4" (13-77mm) O.D. and includes three freezing jackets, two 7.8' (2.4m) hi-pressure hoses, a T connector, and a 20 lb (9.1 kg) CO2 cylinder (unfilled).

Pipe freeze plugging is a simple, cost-effective method to perform pipe maintenance or line modifications without shutting down your plant processes. Using liquid carbon dioxide (CO2) you can isolate the problem area in the line with SOLID freeze plugs of the fluid within the line. This allows the job to be done with no drain-down or refill, no loss of expensive process fluids, and no system downtime. Once the work is completed, the plugs are thawed and the line is back in operation. Standard freeze plugs range in size from ½" to 3" (13-77mm) O.D.

1 unit of 7.8’ (2.4m) High Pressure Hoses with custom nozzle
1 unit of small Jacket for pipes ½" - 1" (13-25 mm) O.D.
1 unit of medium Jacket for pipes 1" - 1½" (25-38 mm) O.D.
1 unit of large Jacket for pipes 2" - 4" (38-114 mm) O.D.
1 Tee connectors
1 Pair Safety Glasses
1 Pair of Insulated Gloves
1 Carrying bag & Instructions for use

Qty: Price: $569.00

Pipe Freezing Operating Instructions Manual PDF


Complete 1/2"-4" Single Freeze Kit with 20' Hoses

Freezing Kit with 20 foot hoses

Qty: Price: $695.00

Pipe Freezing Operating Instructions Manual PDF

The Pipe Freezing Kit eliminates the need to drain systems and shut down operating equipment when making pipe repairs. The kit uses liquid carbon dioxide to create ice plugs in sections of pipes. Kits are supplied with three freezing jackets for pipes ½"-4" (13-77mm) O.D and two 20' hoses.

To operate, turn off the pipe flow and attach a freezing jacket to the pipe upstream from the section needed to be repaired. Fill the freezing jacket with CO2 and an ice plug will form. After completing whatever work is needed, remove the jacket and the ice plug will defrost.

Note:
The Kit can be used for pipes ½"-4" (13-77mm) O.D. and includes three freezing jackets, two 20' (6.1m) hi-pressure hoses, and a T connector.

Pipe freeze plugging is a simple, cost-effective method to perform pipe maintenance or line modifications without shutting down your plant processes. Using liquid carbon dioxide (CO2) you can isolate the problem area in the line with SOLID freeze plugs of the fluid within the line. This allows the job to be done with no drain-down or refill, no loss of expensive process fluids, and no system downtime. Once the work is completed, the plugs are thawed and the line is back in operation. Standard freeze plugs range in size from ½" to 3" (13-77mm) O.D.

1 unit of 20’ (6.1m) High Pressure Hoses with custom nozzle
1 unit of small Jacket for pipes ½" - 1" (13-25 mm) O.D.
1 unit of medium Jacket for pipes 1" - 1½" (25-38 mm) O.D.
1 unit of large Jacket for pipes 2" - 4" (38-114 mm) O.D.
1 Tee connectors
1 Pair Safety Glasses
1 Pair of Insulated Gloves
1 Carrying bag & Instructions for use

Qty: Price: $695.00

Pipe Freezing Operating Instructions Manual PDF


Complete 1/2"- 4" Dual Freeze Kit

Dual Pipe Freezing Kit

Qty: Price: $989.00

Pipe Freezing Operating Instructions Manual PDF

The Pipe Freezing Kit eliminates the need to drain systems and shut down operating equipment when making pipe repairs. The kit uses liquid carbon dioxide to create ice plugs in sections of pipes. Kits are supplied with three freezing jackets for pipes ½"-4" (13-101mm) O.D.

To operate, turn off the pipe flow and attach a freezing jacket to the pipe upstream from the section needed to be repaired. Fill the freezing jacket with CO2 and an ice plug will form. After completing whatever work is needed, remove the jacket and the ice plug will defrost.

Note:
The Kit can be used for pipes ½"-4" (13-101mm) O.D.

Pipe freeze plugging is a simple, cost-effective method to perform pipe maintenance or line modifications without shutting down your plant processes. Using liquid carbon dioxide (CO2) you can isolate the problem area in the line with SOLID freeze plugs of the fluid within the line. This allows the job to be done with no drain-down or refill, no loss of expensive process fluids, and no system downtime. Once the work is completed, the plugs are thawed and the line is back in operation. Standard freeze plugs range in size from ½" to 4" (13-101mm) O.D.


4 units of 7.8’ (2.4m) High Pressure Hoses with custom nozzle
2 units of small Jacket for pipes ½" - 1" (13-25 mm) O.D.
2 units of medium Jacket for pipes 1" - 1½" (25-38 mm) O.D.
2 units of large Jacket for pipes 2" - 4" (38-114 mm) O.D.
2 Tee connectors
2 Pair Safety Glasses
2 Pair of Insulated Gloves
1 Carrying bag & Instructions for use

Qty: Price: $989.00

Dual-Freeze-Kit-Operating-Instructions-PFK-DBL-5-3.pdf


Operating Instructions – Pipe Freezing Kit Model PFK-5-3
Freeze Jacket In Action Freezing Pipe Freeze Kit Display Pipe Is Frozen... Freeze Kit Install Pipe Freezing Kit
*Kit does not include Co2 bottle or cart however you can easily buy the Co2 bottles locally.

GENERAL:

The 2LBin.com pipe freezing kit uses liquid carbon dioxide to freeze stationary water in pipes. A very low "dry ice" temperature (-109ºF/-78ºC) inside the freezing jacket creates a secure ice plug within the pipe and blocks the flow of liquid, allowing repairs or modifications to be made to the piping system without draining or shutting down the entire system. Three freezing jackets, for 1/2" through 4" pipe, are supplied with the 2LBin.com Freezing Kit. The pipe freezing technique can be used on iron, lead, steel, copper, and plastic pipe. The 2LBin.com pipe freezing kit does not come with an empty CO2 cylinder. Check the local telephone directory or yellow pages for a source of CO2. Look under the headings "Gas-Bottled and Bulk" or "Welding Equipment and Supplies"

NOTE:
The freeze kit will work only with a tank fitted with a siphon. A siphonless tank will not feed liquid CO2 -CO2 gas will not freeze pipes

 

GETTING READY:

1. Prepare the pipe to be frozen as follows:

a. Stop the flow of water through the pipe. Moving water will not freeze.
b. Water temperature should be at room temperature (75ºF/24ºC) or colder whenever possible. Warmer water takes much longer to freeze and hot water will not freeze.
c. Thoroughly clean the section of pipe to be frozen. Dirt and layers of paint will lengthen the freezing process.

2. Check all hoses, freezing jackets, threaded parts and nozzle for wear and replace any worn components. Make sure the nozzle is clean and clear.

FREEZING PIPES

  1. Select the proper size freezing jacket based on the size of the pipe to be frozen.
  2. Connect nozzle assembly to jacket, making sure that the nut inside of the brass grommet on the jacket is tightened securely to prevent leakage.
  3. Connect hose to the nozzle assembly and to the CO2 cylinder and tighten securely to prevent leakage.
  4. While holding the jacket firmly to prevent the nozzle from whip lashing, briefly open the valve on the cylinder to make sure the nozzle is clear.
  5. Determine the correct freeze location taking into account the following points:
      1. Always keep the freezing point 3 feet or more from a closed valve or connection.
      2. Always keep the freezing point 3 feet or more from another freeze. NOTE: failure to observe this 36 inch margin of safety can result in damage to pipe due to the expansion of water as it freezes.
      3. If torch cutting, welding or soldering is to be performed on the pipe, keep the freeze at least one foot from work for each inch of pipe diameter when working on carbon steel or iron pipe. Triple the distance on copper pipe. Cutting, welding or soldering too close to the freeze can damage the ice plug.
  6. Wrap the freezing jacket around the pipe using the Velcro strips to seal the jacket in place and tie the cords tightly around the ends of the jacket. After this step, the use of protective gloves is recommended to prevent frostbite.
  7. Completely open the valve on the CO2 cylinder.
  8. Squeeze the jacket while injecting CO2 to form a solid, even block of dry ice around the pipe. Crush any lumps that form in the ice.
  9. The following chart applies to freezing completely stationary, 70ºF water in carbon steel pipe. Adjust times according to actual conditions, allowing more time for warmer water or slight flow of water.
  10. Multiply all times by 3 for plastic pipe.
    
JACKET SIZE SMALL MEDIUM LARGE
Pipe Size ½" ¾" 1" 1½" 2" 3" 4"
Injection 1 Min. 1.5 Min. 2 Min. 5 Min. 8 Min. 10 Min. 8 Min.
Waiting Time 3 Min. 5 Min. 5 Min. 5 Min. 5 Min. 5 Min. 10 Min.
# Of Injections 2 2 3 3 3 5 7
Total Time 8 Min. 13 Min. 21 Min. 30 Min. 39 Min. 75 Min. 126 Min.
CO2 Consumption 1½ Lbs. 2 lbs. 4 lbs. 10 lbs. 20 lbs. * 40 lbs.* 65 lbs.*
Keep extra filled CO2 cylinders on hand. Have at least 2 full cylinders available when freezing 2-inch pipe, and 3-4 full cylinders for 3 and 4 -inch pipe. All cylinders must be equipped with a siphon and must be kept upright when in use.
 
A full 20 pound CO2 cylinder contains about 18 pounds of usable CO2 and weighs 45 Pounds. An empty cylinder weighs 27 pounds. Weigh the cylinder between freezes to determine its approximate content.
  1. If you are unable to form a solid dry ice pack, check the nozzle for blockage, make sure the CO2 cylinder is not empty, and make sure the water flow in the pipe is turned off.
  2. Continue shaping the dry ice pack at 10 minute intervals during the freezing process. For optimum results, keep the ice pack formed tightly around the pipe.
  3. When the injection process is completed, frost should be formed on the outside of the pipe at the edges of the jacket. This indicates that the contents of the pipe are completely frozen. As long as this frost remains dry and stable, the freeze is being properly maintained.
  4. Leave the freezing jacket on the pipe while performing pipe maintenance.

As a safety precaution, make additional 30-second injections every 15 minutes.

When work is completed, remove the freezing jacket from the pipe and allow the freeze to thaw naturally. Do not attempt to thaw the freeze with a torch as thermal shock damage to the pipe can occur. Always wear protective gloves when handling jacket, dry ice pack or frozen pipe.

IMPORTANT INFORMATION ON CO2 AND CO2 CYLINDERS

  1. All A. Gur's CO2 cylinders are equipped with a siphon to drain liquid CO2 from the bottom of the cylinder. CO2 gas will not form dry ice.
  2. All A. Gur's CO2 cylinder valves are fitted with a safety-bursting disc to protect against over pressurization. If the cylinder is overfilled or subjected to temperatures over 100ºF, the bursting disc may rupture, allowing violent discharge of CO2 gas.
  3. Always weigh tanks to prevent overfilling.
  4. Store all CO2 cylinders out of sunlight and away from heat.
  5. Never transport cylinders in the driver's compartment of vehicle as sudden rupture of the bursting disc could distract the driver.
  6. The A. Gur's pipe freezing kit works best when the cylinder temperature is kept below 77ºF. It will not work if the cylinder temperature reaches 88ºF.

CAUTION: CO2 is heavier than air and will collect in confined or low-lying work areas. Always make sure there is good ventilation to prevent suffocation. CO2 gas is odorless and invisible. Disperse CO2 before entering a confined or low-lying work area.


Freeze Jackets All Aluminum

Freeze JacketFreeze JacketFreeze Jacket  Freeze Hoses    
Click to enlarge pictures our custom freeze jackets


Freeze in Action Freeze Jacket Ready for a Freezing Freeze Jacket Ready for a Freezing Freeze Jacket Ready for a Freezing Freeze Jacket Ready for a Freezing
Some past jobs completed with our equipment:

Our single wall aluminum freeze jackets are commercial quality graded and are used by PipeFreeze technicians.  Single wall jackets are best suited for tight locations, are light weight for transportation, and allow single technician assembly. All 2LBin jackets are designed for use in both horizontal and vertical PipeFreeze applications. National Iron Pipe Threads are provided for nitrogen input and for gas exhaust and all jackets above 3” are provided with two input feeds for continual nitrogen feed. (Double wall jackets are available, priced per application)

*Freeze Jackets All Aluminum

Qty. 

Item #

Price

Delivery Apx.

IP Feed IP Exhaust

Min. Clamps Required

Qty:

3/4” – 1 ¼ Jacket

1

SFJ-750-125

450.00

3 weeks

(1) -¾” in - 1” out

4

Qty:

1 1/2 – 2” Jacket

1

SFJ-150-200

525.00

3 weeks

(1) - ¾” in - 1” out

4

Qty:

2 1/2” Jacket

1

SFJ-250-000

575.00

3 weeks

(1) ¾” in
(1) 1” out

4

Qty:

3” Jacket

1

SFJ-003-001

795.00

3 weeks

(2) 3/4” in
(2) 1 1/4” out

6

Qty:

4” Jacket

1

SFJ-004-001

1,225.00

3 weeks

(2) 1” in
(2) 1 1/2” out

6

Qty:

5” Jacket

1

SFJ-005-001

1,610.00

3 weeks

(2) 1” in
(2) 2” out

8

Qty:

6” Jacket

1

SFJ-006-001

1,730.00

3 weeks

(2) 1” in
(2) 2” out

8

Qty:

8” Jacket

1

SFJ-008-001

2,410.00

3 weeks

(2) 1” in
(2) 2” out

8

Qty:

10” Jacket

1

SFJ-010-001

2,950.00

3 weeks

(2) 1” in
(3) 2” out

10

Qty:

12” Jacket

1

SFJ-012-001

3,550.00

3 weeks

(2) 1” in
(3) 3” out

10

Qty:

Freeze Jacket Clamp

1

M10-L-5

53.00 each

3 weeks

 (3) Weeks

 
Qty:

Freeze Jacket Hose

 1

H1-L-001

345.00 each

3 weeks

 (3) Weeks

 
*Jackets fit Copper & Steel O.D.’s *Single Wall *Non-Insulated

Handheld Thermocouple Thermometers

This device contains a variety of probes and meters for many field applications. Specifications: Dual J-K-T-E Thermometer lets you select from four thermocouple types--J, K, T or E. Accepts up to two thermocouple inputs. Manually stores up to 25 readings. Accuracy: ±0.1%. Type J and K Thermometers feature four-button keypad, on/off, °C/°F and Hold. Accuracy: ±0.2%. Stainless steel probes have 5-1/2"L glass-filled nylon handles and 5'L coiled PVC cables. Use General-Purpose Probe for liquids, gases or small surfaces. Penetration Probe penetrates soft or semi-soft materials. Air/Gas Temperature Probe features built-in perforated tip shield. Use Surface Temperature Probe for surfaces such as hot plates. Hypodermic Probe penetrates soft tissues and liquids without disturbing large sample areas. Roller Probe measures moving rollers and similar convex surfaces. Thermocouple Thermometry Kit includes either a J or K thermometer, three probes (general-purpose, air/gas and surface), 9V battery, instructions and case. Carrying Cases keep a meter and one probe together for quick, convenient access. Carrying Case with Window protects your meter while in use. Compliance: UL and cUL rated. Intrinsically safe for Class 1, Division I, Groups A, B, C, D hazardous locations. No. 40488 rated IP54, splash and dust resistant.

Hand-Held Thermocouple Thermometers: 289.00
Qty:

Surface Probe:
108.80
Qty:
Handheld Thermocouple Thermometers

Waterproof Dissolved Oxygen Meter

Don’t be fooled by their size—these compact, portable units can detect hazardous gases in seconds. They have a digital readout and an audible warning signal with a rating of 85 dB. All have a high-intensity LED light that brightens when the audible alarm sounds. A calibration check must be performed on the detector before each use to verify that it is working properly. Calibration test kits for carbon monoxide and hydrogen sulfide detectors are sold separately. Temperature range is -4° to +122° F. For use in Class 1, size is 4" Lg.× 2" Wd.× 1" Ht. Detectors, with non-replaceable batteries, should be thrown away after their two-year lifespan expires. All have a vibration alarm and operate on one non-replaceable lithium battery (included). Size is 3" Lg.× 2" Wd.× 1" Ht. Calibration test kits are sold separately, maintain the accuracy of the detectors. They include a cylinder of gas, regulator, tubing and carrying case.

Qty: Price: $299.95
Waterproof Dissolved Oxygen Meter

Qty: Price: $425.00

20' High Pressure Hoses with the custom nozzle

Freezing Kit 20foot Hoses

Services

IFT Globe Logo for PipeFreeze.com

  • Pipe Freeze, Pipe Freezing Standard pipe freeze plugs range in size from 1/2" to 36" OD and can be performed on most fluids including petrochemicals up to 3000 PSI.
  • Bypass, Bypassing We can provide the most advanced line stopping and bypassing service available today! Sizes from 1/2" - 48" on any type of pipeline.
  • Hot, Wet, Pressure, Tapping Hot tapping services include tapping 1/2" to 96" on natural gas, water, sewage, steam, petroleum products, and chemicals.
  • Linestop, Line Stopping We can perform sewer plug services on steam systems, air lines, chemical, sewage lines and chilled water systems Pressures through 500 psi and temperatures through 500 deg. F.
  • Other Services

  • Industrial Pipe Freeze Services Our pipe freeze services can locate a pinhole size leak on gas, water and most fluids filled pipline.
  • Team/Occlude Insert Valve Install This valve install is a real AWWA spec C515 valve designed for continuous use and is installed without a system shutdown.
  • Wall, Vessel, Tank Tapping Our wall tapping assemblies are used for hot tapping onto concrete walls, concrete storage tanks, and large diameter concrete conduits with any size outlet through 120", in 125, 150, and 300 lb. classes.
  • IFT Cut Sheets This is our useful website deducated to supplying a printable format for our cut sheets and other details pertaining to our work scope.
  • Other Pipeline Services Visit our main website at www.Hottap.com for a full list of our services
  • Free Quote

  • Pipe Freeze Quote Get a quick quote on our freeze plug services up to 36"and pressures as high as 3000 psi.
  • Hottap Linestop Bypass Quote Get a quote on hottaps up to 96", linestops up to 72" and bypasses up to 48" on all types of pipeline.
  • Wall Tank Vessel Tap Quote We can quote up to 120” taps on concrete walls, storage tanks & large diameter concrete conduits.
  • Insert Valve Install Quote Get a quote on 4", 6", 8", 10" & 12" Insert Valve installations onto Steel, PVC, C-900, Cast-Iron, Ductile-Iron and A/C pipeline.